whomop.blogg.se - Clear networx

Clear networx code#

We recommend, for ease of programming, that you write your zone numbers down on a sheet of paper and then to the right of each zone number write its zone definition. Each zone will be its own segment and there will be toggle options that can be turned on and off by pressing the corresponding number. This is true with the partition locations as well. After entering the definition you will press * to advance to the next segment. To program the zone definitions for each zone you will go into each location and input a zone definition into the appropriate segment. For example Location 26 is used to assign zones 1-8 to whatever partition you’re using them on. You will then have the next location for assigning zones to different partitions. For instance Location 25 is zone definition programming for zones 1-8. Each location will correspond to a set of 8 zones. NetworX NX8 & NX8E will have locations 25-36. Depending on the model of Interlogix NetworX panel you have the locations may differ. Zone definitions are programmed in locations 25 to 36. Step 8 –Zone Definition Programming (Locations 25 to 36) Segments 5 & 6 are not used so you can just press * through these. Segment 4 – Exit Time 2 (45-255 seconds).Segment 3 – Entry Time 2 (30-255 seconds).Segment 2 – Exit Time 1 (45-255 seconds).Segment 1 – Entry Time 1 (30-255 seconds).When you enter this location you will enter the first value in the first segment and then press * to move to the next segment. You will now set you entry and exit delays for any doors. You will then press # to exit location 42.You will then press * * to skip the last two segments. Continue to do this until you have entered in all 4 digits of your new Programming Code.

Clear networx code#

You will enter the first digit of your new Programming Code and then press * to advance to the next segment (digit). Each digit of the Programming Code is referred to as a segment.

You will then be presented with ‘Loc # 42 Segment #1’.

To change the program (installer) code you will need to enter, when asked to enter location, 42 and then #.

We recommend that you do this as any burglar could research the default codes for a system.

Step 6 – (Location 42) Change Programming Code Locations are programming sections and we will cover these below

You will then see ‘Enter location, then #’.

The device address for panel programming is 0

You will then see ‘Enter device address and then press #’.

To enter into the panel’s programming section you will enter * + 8 + Programming Code.

When finished press # while the ‘Ready’ LED is flashing.

If you need to enter another code repeat the process above. If it was rejected then you’ll hear it beep 3 times. The ‘Ready’ light will then begin to flash again letting you know it was accepted.

You will then enter a 4-digit code for that user.

You will then enter in the three digit user code slot you’d like to change (001-040).

Then press # to exit back to main screen.

Continue to set the time a date sections, using the up/down arrows, one at a time pressing * after each section to accept until the time and date are set to your preference.

Use the up/down arrow keys to set the hour to AM or PM hour then press * to move to minutes.

You will then see the time and date displayed with the HOURS section flashing.

4=On suppresses beeps when an RF transmission is lost.

3=On if PIN should be hidden when programming.

2=Disable LED Extinguish on this keypad.

SELECT AN OPTION: Programs special characteristics.

Prevents over-writing the custom message during keypad copy.

Custom Message Lock - Enable Custom Message Lock.

Clock – Enable or Disable Clock display.

Custom Message – Enables or Disables Custom Message display.

Enable temporary viewing of all partitions by pressing *, 1, partition number. If there is a system problem, pressing *2, shows the service menu. Will not allow the Service LED to light for any reason. Sounds a short beep to verify that the keypress was accepted.

Enable panic, fire, emergency beep tone.

Will not allow the keypad to display faulted or bypassed zones when the system is armed. Silences the pulsing keypad sounder for 5 seconds when a key is pressed. Silences the entry/exit sounder and chime only.

Press * after enabling/disabling the desired functions.

You will be presented with options, one at a time, that will enable/disable the functions for the keypad shown in the list below.

Step 2 – Set keypad options (For LCD Keypads) The keypad will automatically exit the keypad programming after this

You will now enter the partition you want the keypad to be assigned to.

The Instant LED will illuminate steady and the Service LED will remain flashing

The Service LED and the Instant LED will flash on the keypad that you are working on Step 1 – Assign keypad number and partition You will then be asked to enter location.Total Connect 2.0 Package Monitoring Add-Ons.Central Station Alarm Monitoring Services.